HVAC Repair Denver Tech Center

Posted in HVAC Contractors Denver on January 30, 2018
Tags: , , , , , , , , , , , , , , , , , , , , , , , , , ,

You're a homeowner and determined your home's air conditioning needs fixing or needs to be replaced with a newer, more efficient system. You're all set to get moving. What's the optimal way to get a high quality HVAC contractor who will do a good job for a fair price? What could you look for in an air conditioning contractor to obtain this work? Denver Tech Center 

Furnace Boiler Repair

When homeowners choose to repair an air conditioning system or replace the unit with a newer one, they're often plagued by worries that their family will swelter while the job is completed.  These concerns are perfectly normal and common among many homeowners looking for HVAC fixes or air conditioner repair specialists.

Denver Tech Center

Gas Heating System Service To fix household things that break, you need to know how it works, what can go wrong, how to identify the problem, as well as the steps to fixing it. Here's what you need to know about gas furnace repairs.How Does It Work?Natural or propane gas from an outside source is piped to the furnace where it is burned to produce heat. Usually a fan-driven forced-air distribution system blows the warmed air through ducts that vent into the various rooms of the house. Older gas furnaces use a standing-pilot ignition. Maintenance involves turning off the pilot each spring and relighting it each fall. Newer, more efficient gas furnaces use an electric spark to light the gas as necessary.What Can Go Wrong?Most gas furnaces are quite reliable. What are the symptoms of problems? The furnace may not produce heat or may not produce enough heat. The pilot light may go out repeatedly or refuse to light. The thermocouple may be faulty. The pilot may light but not ignite the burner. The furnace may be noisy. There are some maintenance and a few minor repairs that you can make. However, major service should be left to a trained technician.Fix-It TipTo minimize problems with your gas furnace, take time each month to check the air filter and clean or replace it if necessary. Once a year, clean the blower blades, lubricate the blower motor, and inspect the belt.How Can I Identify the Problem? If there is no heat, check the electrical service panel for a burned fuse or tripped breaker. Relight the pilot light (see below).If there is not enough heat, adjust the burner air shutter (see below); and clean the burner ports (see below).If the pilot light does not light or does not stay lit, clean the pilot orifice carefully with a toothpick, test the thermocouple and replace it if it is faulty (see below).If the flame flickers, adjust the pilot (see below).If there is an exploding sound when the burner ignites, adjust the pilot to a higher setting and clean the pilot orifice and the burner ports.If the burner takes more than a few seconds to ignite, clean the pilot orifice and adjust the pilot light.If the burner flame is uneven, clean the burner ports. If the burner flame is very yellow, clean the burner; open vents in the furnace room to provide more air; adjust the burner air shutter.If the furnace makes a rumbling noise when the burners are off, clean the burner and adjust the burner air shutter.If the air is too dry, wash or replace the evaporator pad if you have a humidifier; test the humidistat; and adjust the water-level float to raise the water level.If some rooms are too cool and others too warm, the distribution system may require balancing. Refer to the Forced-Air Distribution Fix-It Guide at FixItClub.comFix-It TipBe sure your filter is the right size for your furnace.What Parts, Materials, and Tools Do I Need?Some replacement parts for gas furnaces are interchangeable (filters, fasteners) and available at your local hardware store. Others, such as burners and controls, must be purchased from the manufacturer or aftermarket supplier or through a heating equipment supplier listed in your local telephone book.The primary tools you will need for fixing a gas furnace include these:* Screwdrivers* Wrenches* Pliers* Wire brush* MultimeterWhat Are the Steps to Fixing It?To light the pilot on a standing-pilot (always on) ignition system, follow the lighting instructions located near the control. Otherwise, try these steps:Light the pilot:1. Press and hold the pilot control knob to start the pilot. Set the control knob to the pilot position. Hold a long match under the pilot gas port.2. Press the control knob; the pilot should light. Hold the control knob down until the flame is burning brightly (about 30 seconds). Release pressure on the knob, and turn it to the on position.3. If the pilot goes out when you release the control knob, try relighting, holding the control knob down longer. If the pilot again goes out, check the thermocouple (below).Adjust the pilot:1. Remove any cap covering the pilot adjusting screw on a combination control. 2. Turn the adjusting screw counterclockwise to increase the flame or clockwise to decrease it. It is correctly adjusted when the flame envelops the thermocouple bulb by 1/2 inch and appears dark blue with a small yellow tip.Test and replace a thermocouple:1. Hold the control knob to pilot and light the pilot as above.2. Unscrew the thermocouple fitting with an open-ended wrench.3. Set a multimeter to the DVC (lowest voltage) scale.4. Clip one multimeter lead to the end of the thermocouple tube nearest the pilot and the other lead to the fitting on the other end of the tube.5. If the multimeter shows a reading besides zero, the thermocouple is functioning. Replace the thermocouple tube.6. If there is no reading, you will need to clean or replace the thermocouple following steps 7 through 11.7. Release the control knob and shut off the main gas valve on the gas-supply pipe that leads into the burner. Shut off power to the burner at the electrical service panel .8. Remove the thermocouple from its mounting bracket.9. Wipe the combination control clean and install a new thermocouple, tightening it by hand, then give it a one-quarter turn with a wrench.10. Insert the thermocouple into the pilot bracket, being careful to not crimp the tubing.11. Turn on power to the furnace and relight the pilot (above).

Heating and Cooling Systems - Correcting Temperatures Differences Between Rooms

Replacing A Gas Furnace Most homeowners think of a broken furnace as one that stops functioning, but that is not always the case. In addition to mechanical failure, there can also be subtle indications that repair is in a furnace's future, that the unit is actually broken but still appears to be functioning. If your furnace displays one or more of the signs below, you should consider it as an indicator that it may need repair, and schedule an appointment with an HVAC technician as soon as possible:The Unit Makes Unusual NoisesNo furnace is completely silent. If you hear unusual banging, whining, or groaning noises emanating from your furnace, it may be a sign that it has difficulty igniting, has a loose belt, or has a worn out part that will soon break. If the noises are caused by something else, you may need to call Ghostbusters instead of an HVAC company. You Need to Set Your Thermostat Higher than NormalWhen a home stops heating well, the response of most homeowners is to raise the thermostat setting. As the problem grows worse, though, even the highest setting can fail to deliver warmth. Before your home reaches this point, have a furnace repair technician perform an inspection. The problem may be a faulty thermostat, a problem with an intermittent pilot ignition system, or even leaky ductwork.Your Energy Bills are Inordinately HighIf your electrical bills are high this winter, it may be because your air distribution fan will not kick off, or because you raise the thermostat setting to compensate for a lack of heat. It could also be that your furnace performs inefficiently due to a clogged air filter or leaky ducts. Instead of paying a utility bill that matches your mortgage payment, call a repair technician instead.The Pilot Light is YellowIf you inspect your furnace and notice that the pilot light is yellow, it may indicate the presence of carbon monoxide. A blue flame indicates the gas mixture is normal; a yellow flame indicates it is not. If carbon monoxide is detected, the technician can determine whether your HVAC equipment or your home is the source of the problem.The Unit has Trouble Kicking On or Staying On If your furnace takes a long time to kick on, or it kicks on as usual but it does not stay on, a broken thermostat, faulty wiring, or a pilot light ignition problem could be to blame. There could also be a problem with the distribution fan motor. Like the other problems in this list, a furnace that has trouble kicking on usually gets worse over time.ConclusionThe need for furnace repair usually occurs at the most inopportune time-when your furnace is busy heating your home. Ann Atlanta heating and air conditioning company that specializes in HVAC repair should be able diagnose and fix the problem quickly. For homeowners, the key is to recognize signs that indicate a furnace needs repair, and schedule an HVAC inspection before it stops working. HVAC Installation Companies

HVAC Contractors Denver

Comments are closed.